electro-music.com   Dedicated to experimental electro-acoustic
and electronic music
 
    Front Page  |  Radio
 |  Media  |  Forum  |  Wiki  |  Links
Forum with support of Syndicator RSS
 FAQFAQ   CalendarCalendar   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   LinksLinks
 RegisterRegister   ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in  Chat RoomChat Room 
 Forum index » DIY Hardware and Software » Ken Stone designs - CGS
DUSG vs VCS
Post new topic   Reply to topic Moderators: Scott Stites
Page 1 of 1 [4 Posts]
View unread posts
View new posts in the last week
Mark the topic unread :: View previous topic :: View next topic
Author Message
roman_f



Joined: Jul 03, 2007
Posts: 63
Location: Moscow
Audio files: 1

PostPosted: Sat Oct 29, 2011 9:32 am    Post subject: DUSG vs VCS Reply with quote  Mark this post and the followings unread

is there any difference?
or 1st module is just 2 VCSs?
Back to top
View user's profile Send private message Visit poster's website
Dave Kendall



Joined: May 26, 2007
Posts: 421
Location: England
Audio files: 3

PostPosted: Sat Oct 29, 2011 1:07 pm    Post subject: Reply with quote  Mark this post and the followings unread

Hi.

As far as I can tell , looking at the schematic, the VCS is a single channel version of the DUSG, but has several added features not found on the DUSG.

* A dedicated cycle switch that is independent of the TRIG in. You can cycle with the DUSG, but need to patch OUT to TRIG in.
* CV inputs for FALL and RISE in addition to the switchable FALL/BOTH/RISE CV input.
* Switches for FALL and RISE to make the responses exponential.
* An additional AC output. (which presumably centres the output around 0V)
* An independent patchable CV processor section.

cheers,
Dave

_________________
"Everything in moderation, including moderation"
Back to top
View user's profile Send private message
sonicwarrior



Joined: Dec 22, 2005
Posts: 266
Location: Cologne, Germany

PostPosted: Mon Jun 18, 2012 3:49 am    Post subject: Reply with quote  Mark this post and the followings unread

The VCS PCB has a MOTM power connector on board which in my eyes is a biiiiiig plus.
Back to top
View user's profile Send private message
otherunicorn



Joined: May 11, 2008
Posts: 136
Location: Australia

PostPosted: Tue Jun 19, 2012 8:26 pm    Post subject: Reply with quote  Mark this post and the followings unread

The primary difference is that the VCS had independent VC control of rise and fall times at all times, while the DUSG lets you control rise OR fall OR both together.
_________________
http://www.cgs.synth.net/
Back to top
View user's profile Send private message Visit poster's website
Display posts from previous:   
Post new topic   Reply to topic Moderators: Scott Stites
Page 1 of 1 [4 Posts]
View unread posts
View new posts in the last week
Mark the topic unread :: View previous topic :: View next topic
 Forum index » DIY Hardware and Software » Ken Stone designs - CGS
Jump to:  

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Forum with support of Syndicator RSS
Powered by phpBB © 2001, 2005 phpBB Group
Copyright © 2003 through 2009 by electro-music.com - Conditions Of Use