Search found 166 matches

Hello All,

Looking for a project to work on during Covid hiatus, I am curious as to what Low-Fi noise maker from MFOS I should build.

Since there are quite a few offerings on the MFOS site, I am ...

Hello all,

I have visited the Mfos site today and the main page says they are off-line. So anyone knows any more details about this? It seems like the catalog is still up and I can put things in ...

iam an anti-expert in terms of expo, but may this helps

https://synthcube.com/cart/ankaeohm-tempco-3300ppm-1-6w-1k-ohm-bag-of-5

edit: found a informative thread about modern tempco replacement o ...

Hello All,

I have a few MFOS projects laying around that I want to get back to building. However, I know one of my problems was trying to find the 3300 Tempco, temperature compensation resistor. ...

OMG! I know I have been out of the loop for a while, but this is shocking news. I lost my mother this past summer and I have been out of the loop with many things. Usually I work on my synth proj ...

You'll need matched 2N3906's as they're PNP rather than 2N3904's which are NPN.

Ok, I wasn't paying attention to that one. Yeah, that would be a big difference, but I have seen cases where you cou ...

Hello All,

Ok, so I bit the bullet and bought 3 PCB's from Fonik to build 3 of these 555-VCO's. For the most part getting the parts isn't too difficult, but it seems the hardest part to get are t ...

555 - VCO Boards received today! What can I say, they are a thing of beauty. Very good quality boards. Now I just have to recall where the BOM was for these.

So far it looks like I am WELL on ...

Whoa!

I don't recall getting an email to send in payment and I checked back here and people are getting their boards?

I'll double check my emails, but I seriously don't remember getting any mess ...

I recommend

I already have Front Panel Designer for Linux. The trouble is I don't really know how to use it. I can set hole sizes and place them, but I am having trouble with making labels.

I ...

i went ahead and drew those parts for you in corel. the dimensions are based off of what datasheets i could find at mouser. let me know where to send the .cdr file

For some reason the file didn't t ...

i went ahead and drew those parts for you in corel. the dimensions are based off of what datasheets i could find at mouser. let me know where to send the .cdr file

I sent you a PM with my email add ...

hi! i use coreldrawx5 for my panels. i have drawn a lot of standard parts as two layer vectors(component and hole). if you'd like , i can send you a .cdr file with a bunch of components that i use a l ...

Hello All,

Ok, I have completed the population of my DIY Synth Experimenter Board and now I have the arduous task of coming up with a face panel design.

I know there is a face panel design on th ...

Hello All,

Just touching base. I have begun to construct the DIY Synth Experimenter board along with a couple other projects I am doing.

Yesterday and today, I spent quite a bit of time on the ...

Ok, guys, fair enough.

Judging by your answers and what I read so far, I think I would be more happy with the 555 VCO than those from MFOS. So I put myself down for 3 555 VCO circuit boards. B ...

3 x VCO Circuit PCB

Shipping to 11702, USA.

Thanx,

Geo

While this replay is mainly for Nicolas, others feel free to chime in.

For a long time I was considering a build of the Variable Skew LFO circuit that is on the MFOS website. However, since that c ...

Hello All,

I just stumbled upon this thread today while looking into some ideas for module VCO's and VC-LFO's.

Up to now I been dealing with MFOS and I have bought some boards from them. I am c ...

Hello All,

Well, it has been a month and 2 days and my order from Futurlec is STILL not here.

The only good thing is that I do have the tracking number and I was able to follow the package from ...

Hello All,

Futurlec gave me the tracking information in regards to my order. As of the 7th, it arrived in NYC. I am HOPING that I will see it by tomorrow or even Saturday. We will see.

I real ...

Hi jukingeo.

I haven't ordered from Futurlec, but I have seen people complaining in other fora about shipping times and changes to shipping costs. However, some here seem to like what they get (eve ...

Also, as I said, my SDIY EB is near completion so I can test out anything you want me to throw at it... .

Sorry I have not responded as of yet, I have been busy with Christmas. We had festivities ...

I can't help you with skew, but I might be able to get you a ramp wave, I posted this earlier without seeing your thread - my schematic might help you and I would like to get some dialog going on modd ...

On the VCA outputs only, you could have a 1/4" & a bannana to cover all audio hook ups .

LOL, I was thinking of that too. Since I had noticed most of the connections on the Experimenter ...

Author	Message
Topic: Which is best? WSG, Noise Toaster, Reverb Rockit, Synth Expe
jukingeo Replies: 2 Views: 3450	Posted: Sun Sep 27, 2020 9:50 am Subject: Which is best? WSG, Noise Toaster, Reverb Rockit, Synth Expe Forum: DIY Hardware and Software » MusicFromOuterSpace.com designs by Ray Wilson
jukingeo Replies: 2 Views: 3450	Hello All, Looking for a project to work on during Covid hiatus, I am curious as to what Low-Fi noise maker from MFOS I should build. Since there are quite a few offerings on the MFOS site, I am ...
Topic: Mfos site up or down?
jukingeo Replies: 1 Views: 3054	Posted: Fri Jan 10, 2020 6:27 am Subject: Mfos site up or down? Forum: DIY Hardware and Software » MusicFromOuterSpace.com designs by Ray Wilson
jukingeo Replies: 1 Views: 3054	Hello all, I have visited the Mfos site today and the main page says they are off-line. So anyone knows any more details about this? It seems like the catalog is still up and I can put things in ...
Topic: 3300 Tempco Availability
jukingeo Replies: 2 Views: 4642	Posted: Sat Jul 13, 2019 5:01 pm Subject: 3300 Tempco Availability Forum: DIY Hardware and Software » MusicFromOuterSpace.com designs by Ray Wilson
jukingeo Replies: 2 Views: 4642	iam an anti-expert in terms of expo, but may this helps https://synthcube.com/cart/ankaeohm-tempco-3300ppm-1-6w-1k-ohm-bag-of-5 edit: found a informative thread about modern tempco replacement o ...
Topic: 3300 Tempco Availability
jukingeo Replies: 2 Views: 4642	Posted: Sat Jul 06, 2019 10:07 am Subject: 3300 Tempco Availability Forum: DIY Hardware and Software » MusicFromOuterSpace.com designs by Ray Wilson
jukingeo Replies: 2 Views: 4642	Hello All, I have a few MFOS projects laying around that I want to get back to building. However, I know one of my problems was trying to find the 3300 Tempco, temperature compensation resistor. ...
Topic: Support Ray's Medical Fund
jukingeo Replies: 3 Views: 4218	Posted: Sun Nov 29, 2015 9:26 am Subject: Getting up to speed with Ray and his illness. His site down? Forum: DIY Hardware and Software » MusicFromOuterSpace.com designs by Ray Wilson
jukingeo Replies: 3 Views: 4218	OMG! I know I have been out of the loop for a while, but this is shocking news. I lost my mother this past summer and I have been out of the loop with many things. Usually I work on my synth proj ...
Topic: The VCO-555
jukingeo Replies: 479 Views: 597371	Posted: Tue Apr 08, 2014 4:01 pm Subject: The VCO-555 Forum: DIY Hardware and Software » Thomas Henry designs
jukingeo Replies: 479 Views: 597371	You'll need matched 2N3906's as they're PNP rather than 2N3904's which are NPN. Ok, I wasn't paying attention to that one. Yeah, that would be a big difference, but I have seen cases where you cou ...
Topic: The VCO-555
jukingeo Replies: 479 Views: 597371	Posted: Mon Apr 07, 2014 4:55 pm Subject: Obtaining tempcos and matched transistors for VCO's Forum: DIY Hardware and Software » Thomas Henry designs
jukingeo Replies: 479 Views: 597371	Hello All, Ok, so I bit the bullet and bought 3 PCB's from Fonik to build 3 of these 555-VCO's. For the most part getting the parts isn't too difficult, but it seems the hardest part to get are t ...
Topic: 3rd run for Thomas Henry's 555-VCO and Controller LFO
jukingeo Replies: 87 Views: 129052	Posted: Thu Apr 03, 2014 2:58 pm Subject: 3rd run for Thomas Henry's 555-VCO and Controller LFO Forum: DIY Hardware and Software » fonik's place
jukingeo Replies: 87 Views: 129052	555 - VCO Boards received today! What can I say, they are a thing of beauty. Very good quality boards. Now I just have to recall where the BOM was for these. So far it looks like I am WELL on ...
Topic: 3rd run for Thomas Henry's 555-VCO and Controller LFO
jukingeo Replies: 87 Views: 129052	Posted: Sat Mar 22, 2014 5:24 pm Subject: 3rd run for Thomas Henry's 555-VCO and Controller LFO Forum: DIY Hardware and Software » fonik's place
jukingeo Replies: 87 Views: 129052	Whoa! I don't recall getting an email to send in payment and I checked back here and people are getting their boards? I'll double check my emails, but I seriously don't remember getting any mess ...
Topic: Making a face panel for DIY Synth Experimenter - Help Needed
jukingeo Replies: 10 Views: 7615	Posted: Wed Mar 05, 2014 5:55 pm Subject: Re: Front Panel Designer software Forum: DIY Hardware and Software » MusicFromOuterSpace.com designs by Ray Wilson
jukingeo Replies: 10 Views: 7615	I recommend I already have Front Panel Designer for Linux. The trouble is I don't really know how to use it. I can set hole sizes and place them, but I am having trouble with making labels. I ...
Topic: Making a face panel for DIY Synth Experimenter - Help Needed
jukingeo Replies: 10 Views: 7615	Posted: Wed Feb 26, 2014 7:36 pm Subject: Making a face panel for DIY Synth Experimenter - Help Needed Forum: DIY Hardware and Software » MusicFromOuterSpace.com designs by Ray Wilson
jukingeo Replies: 10 Views: 7615	i went ahead and drew those parts for you in corel. the dimensions are based off of what datasheets i could find at mouser. let me know where to send the .cdr file For some reason the file didn't t ...
Topic: Making a face panel for DIY Synth Experimenter - Help Needed
jukingeo Replies: 10 Views: 7615	Posted: Sun Feb 23, 2014 11:43 am Subject: Making a face panel for DIY Synth Experimenter - Help Needed Forum: DIY Hardware and Software » MusicFromOuterSpace.com designs by Ray Wilson
jukingeo Replies: 10 Views: 7615	i went ahead and drew those parts for you in corel. the dimensions are based off of what datasheets i could find at mouser. let me know where to send the .cdr file I sent you a PM with my email add ...
Topic: Making a face panel for DIY Synth Experimenter - Help Needed
jukingeo Replies: 10 Views: 7615	Posted: Sat Feb 22, 2014 6:40 pm Subject: Making a face panel for DIY Synth Experimenter - Help Needed Forum: DIY Hardware and Software » MusicFromOuterSpace.com designs by Ray Wilson
jukingeo Replies: 10 Views: 7615	hi! i use coreldrawx5 for my panels. i have drawn a lot of standard parts as two layer vectors(component and hole). if you'd like , i can send you a .cdr file with a bunch of components that i use a l ...
Topic: Making a face panel for DIY Synth Experimenter - Help Needed
jukingeo Replies: 10 Views: 7615	Posted: Sat Feb 22, 2014 1:00 pm Subject: Making a face panel for DIY Synth Experimenter - Help Needed Forum: DIY Hardware and Software » MusicFromOuterSpace.com designs by Ray Wilson
jukingeo Replies: 10 Views: 7615	Hello All, Ok, I have completed the population of my DIY Synth Experimenter Board and now I have the arduous task of coming up with a face panel design. I know there is a face panel design on th ...
Topic: Adding a skew control to the LFO on Synth Experimenter board
jukingeo Replies: 12 Views: 13110	Posted: Sun Jan 26, 2014 8:13 am Subject: Adding a skew control to the LFO on Synth Experimenter board Forum: DIY Hardware and Software » MusicFromOuterSpace.com designs by Ray Wilson
jukingeo Replies: 12 Views: 13110	Hello All, Just touching base. I have begun to construct the DIY Synth Experimenter board along with a couple other projects I am doing. Yesterday and today, I spent quite a bit of time on the ...
Topic: The VCO-555
jukingeo Replies: 479 Views: 597371	Posted: Sat Jan 25, 2014 10:05 pm Subject: The VCO-555 Forum: DIY Hardware and Software » Thomas Henry designs
jukingeo Replies: 479 Views: 597371	Ok, guys, fair enough. Judging by your answers and what I read so far, I think I would be more happy with the 555 VCO than those from MFOS. So I put myself down for 3 555 VCO circuit boards. B ...
Topic: 3rd run for Thomas Henry's 555-VCO and Controller LFO
jukingeo Replies: 87 Views: 129052	Posted: Sat Jan 25, 2014 9:58 pm Subject: 3rd run for Thomas Henry's 555-VCO and Controller LFO Forum: DIY Hardware and Software » fonik's place
jukingeo Replies: 87 Views: 129052	3 x VCO Circuit PCB Shipping to 11702, USA. Thanx, Geo
Topic: Can anyone suggest an LFO...?
jukingeo Replies: 74 Views: 130177	Posted: Sat Jan 25, 2014 12:13 pm Subject: Can anyone suggest an LFO...? Forum: DIY Hardware and Software
jukingeo Replies: 74 Views: 130177	While this replay is mainly for Nicolas, others feel free to chime in. For a long time I was considering a build of the Variable Skew LFO circuit that is on the MFOS website. However, since that c ...
Topic: The VCO-555
jukingeo Replies: 479 Views: 597371	Posted: Sat Jan 25, 2014 10:27 am Subject: The VCO-555 Forum: DIY Hardware and Software » Thomas Henry designs
jukingeo Replies: 479 Views: 597371	Hello All, I just stumbled upon this thread today while looking into some ideas for module VCO's and VC-LFO's. Up to now I been dealing with MFOS and I have bought some boards from them. I am c ...
Topic: Adding a skew control to the LFO on Synth Experimenter board
jukingeo Replies: 12 Views: 13110	Posted: Mon Jan 13, 2014 6:48 pm Subject: Futurelec order update Forum: DIY Hardware and Software » MusicFromOuterSpace.com designs by Ray Wilson
jukingeo Replies: 12 Views: 13110	Hello All, Well, it has been a month and 2 days and my order from Futurlec is STILL not here. The only good thing is that I do have the tracking number and I was able to follow the package from ...
Topic: Adding a skew control to the LFO on Synth Experimenter board
jukingeo Replies: 12 Views: 13110	Posted: Thu Jan 09, 2014 5:27 pm Subject: Adding a skew control to the LFO on Synth Experimenter board Forum: DIY Hardware and Software » MusicFromOuterSpace.com designs by Ray Wilson
jukingeo Replies: 12 Views: 13110	Hello All, Futurlec gave me the tracking information in regards to my order. As of the 7th, it arrived in NYC. I am HOPING that I will see it by tomorrow or even Saturday. We will see. I real ...
Topic: Adding a skew control to the LFO on Synth Experimenter board
jukingeo Replies: 12 Views: 13110	Posted: Sat Jan 04, 2014 7:55 pm Subject: Re: Futurlec Forum: DIY Hardware and Software » MusicFromOuterSpace.com designs by Ray Wilson
jukingeo Replies: 12 Views: 13110	Hi jukingeo. I haven't ordered from Futurlec, but I have seen people complaining in other fora about shipping times and changes to shipping costs. However, some here seem to like what they get (eve ...
Topic: Adding a skew control to the LFO on Synth Experimenter board
jukingeo Replies: 12 Views: 13110	Posted: Sat Dec 28, 2013 2:06 pm Subject: Adding a skew control to the LFO on Synth Experimenter board Forum: DIY Hardware and Software » MusicFromOuterSpace.com designs by Ray Wilson
jukingeo Replies: 12 Views: 13110	Also, as I said, my SDIY EB is near completion so I can test out anything you want me to throw at it... . Sorry I have not responded as of yet, I have been busy with Christmas. We had festivities ...
Topic: Adding a skew control to the LFO on Synth Experimenter board
jukingeo Replies: 12 Views: 13110	Posted: Sun Dec 22, 2013 12:59 pm Subject: Adding a skew control to the LFO on Synth Experimenter board Forum: DIY Hardware and Software » MusicFromOuterSpace.com designs by Ray Wilson
jukingeo Replies: 12 Views: 13110	I can't help you with skew, but I might be able to get you a ramp wave, I posted this earlier without seeing your thread - my schematic might help you and I would like to get some dialog going on modd ...
Topic: Mixing different shape outputs from the SAME MFOS VCO
jukingeo Replies: 6 Views: 4661	Posted: Sun Dec 15, 2013 12:01 pm Subject: Mixing different shape outputs from the SAME MFOS VCO Forum: DIY Hardware and Software » MusicFromOuterSpace.com designs by Ray Wilson
jukingeo Replies: 6 Views: 4661	On the VCA outputs only, you could have a 1/4" & a bannana to cover all audio hook ups . LOL, I was thinking of that too. Since I had noticed most of the connections on the Experimenter ...